Building a PCR instrument on an embedded module: what the electronics actually have to do

PCR thermal cycler with a 96-well plate being loaded by a gloved technician

Thermal cyclers, nucleic acid extractors and protein assay readers look like lab instruments but they are embedded systems with three hard requirements: timing, thermal control and traceability. This note describes the part of the design a single-board computer or system-on-module can carry, and where it should stay out of the way.

What the instrument actually requires

  • Deterministic thermal cycling. Ramp rates, hold times and lid temperature are closed-loop control tasks on the millisecond scale. They belong on an MCU or FPGA, not on a Linux scheduler.
  • Optical readout. Fluorescence channels are usually a LED excitation path plus a photodiode or PMT and a high-resolution ADC. The host board sequences the channels, averages the signal and stores the curve.
  • Traceability. Every run needs a tamper-evident log: protocol version, calibration coefficients, operator, timestamps. A run log has to survive a power cut mid-cycle.
  • Operator interface. A 7 to 10 inch panel with glove-friendly targets, plus USB for a barcode scanner and a thermal printer.
  • Service life. An instrument is sold once and serviced for eight to ten years. The board family has to stay available that long, with a documented BSP.

Recommended configuration

Function Recommended TOPEET part
Main host: UI, run log, LIMS/EHR link, Ethernet iTOP-RK3568 Single Board Computer (industrial -40 to +85 C SKU)
Compact benchtop reader or handheld analyser iTOP-RK3562 Single Board Computer
Low-cost front panel of a sample-prep module iTOP-RK3506 Single Board Computer
Panel 10.1-inch LVDS Display, 1280x800 or 10.1-inch Capacitive HMI Panel
Module for your own carrier iTOP-RK3568 Connector SoM

Why the RK3568 fits: two Gigabit Ethernet ports (instrument network plus a service port), CAN and RS-485 to the thermal controller, one 4-lane MIPI-CSI for a camera that images the reaction block or a gel, LVDS and eDP for the panel, SATA for local run archives, and 0.8 TOPS of NPU that is enough for barcode and cap-reader vision without a discrete accelerator.

Interface checklist

  • Thermal controller link: RS-485 or CAN, with the cycle profile sent as a table and executed locally.
  • Optics: SPI or parallel ADC on the MCU side; the SBC receives averaged counts over the same serial link.
  • Panel: LVDS for a fixed instrument panel, MIPI-DSI if the enclosure is small.
  • Barcode scanner and printer: USB host, no hub required.
  • Power: 12 V DC input on the carrier; add a supervised 5 V rail for the MCU domain so the host can be rebooted without losing the thermal state.

What we would validate with you

Ramp-time jitter under load, log integrity across an interrupted run, fan and Peltier noise on the ADC rails, and panel readability under the instrument's own lid lighting. These are the four issues that decide whether a prototype becomes a product.

Documents

The English datasheet, hardware manual, schematic and BSP source for each board are in the resource portal; registration is required. Every board ships with a 12-month warranty and engineering support by email.

Frequently asked questions

Can the single board computer run the thermal cycling loop?

No. Ramp rates, hold times and lid temperature are millisecond-scale closed-loop tasks that belong on an MCU or FPGA, not on a Linux scheduler. The board carries the layer above it: operator UI, the run log, LIMS or EHR links, Ethernet and the panel.

Which board for a full benchtop instrument versus a compact reader?

The industrial iTOP-RK3568 (-40 to +85 C SKU) is the main host for a full instrument. The iTOP-RK3562 suits a compact benchtop reader or handheld analyser, and the iTOP-RK3506 covers the low-cost front panel of a sample-prep module.

What should be validated first on a thermal cycler design?

Ramp-time jitter under load, log integrity across an interrupted run, fan and Peltier noise on the ADC rails, and panel readability under the instrument's own lid lighting. These four decide whether a prototype becomes a product.

0 comments

Leave a comment

Please note, comments need to be approved before they are published.